HoverTrowel - Other Equipment

AGGREGATE BROADCASTER

Download Ag Blower Prices & Operating Procedures (PDF, 188k)
(You will need the most recent version of Adobe Acrobat Reader™ installed to view this file.)

This heavy duty industrial blower will place decorative quartz, sand, fillers, non-skid and other aggregates at a rate up to 33 pounds per minute into uncured epoxies, vinyl esters, polyesters and more.

The coated carbon steel hopper has a 300 pound capacity and can spray approximately 2,500 square feet without moving the unit. It has a two-speed high volume electrically powered (115vac, 50-60 hz, 9.8 amp) blower.

The unit is very low maintenance, quick and easy to fill, has a balanced tilt back design, and the 8" wheels make it very mobile.

The unit measures 25"W x 42"H x 38"L with a shipping weight of 165 lbs.

Item Description Part #

Aggregate Broadcaster QS-AB

COMMERCIAL CHIP SPRAYER

Download PDF

The Commercial Chip Sprayer features a 2-speed 2-3HP blower with 150/196 cfm of air with a velocity up to 33,570 fpm. The transfer and metering of the chip is accomplished with a positive, but variable speed auger feed powered by a separate gear reduced motor. The fast application of chips into wet resin eliminates a stop and go procedure. Both motors operate on 110 VAC.

• 15 + Gallon Hopper Capacity
• Increases Production by 10 X
• Even Chip Distribution
• Highly Mobile & Ruggedly Built
• Smooth Walled Flexible Tubing for Good Flow
• Completely Variable Flow of Chips
• Both Motors Operate on Standard 110v

HAND HELD CHIP SPRAYER

• Over 1 Gallon Hopper
• Operates on Std 110v
• All Steel Construction
• Adjustable Air Flow
• Lightweight
• Easy to Use & Maintain

Download PDF

The redesigned handheld Chip Sprayer permits the even distribution of large and small, variegated or mono colored chips for the seamless application. Even distribution will allow for less product waste, and less clean up. The low pressure/high volume blower reduces chip breakage, sometimes found with hand application. The overall length is less than 18", allowing this unit proper operation in confined or open application areas. Extremely high application rates are normal with the Chip Sprayer, and the higher production will pay for this unit with one large project.

STONE BLOWER

The Stone Blower will handle fine sand up to No. 4 stone and has controllable air volume for even distribution. The balanced, close coupled hopper and blower are easy to handle. It sets upright and is stable for filling.

• Adjustable Material Gate
• Holds 2 gallons of Stone
• 25 ft of 3 Wire Cord
• Adjustable Discharge Elbow for Overhead Application
• Weighs 15 lbs. & 19" in Length
• Operates on 115 v

ROLLER SCREED

The Roller Screed offers uniform placement of the mortar and is essential for a consistent and successful epoxy flooring installation. The rear outrigger wheel adds greater stability than conventional screed boxes. The position of this rear wheel has eliminated the need to add weight to the front of the units to reduce inconsistencies of the operator.

There is no need to add any additional weight to the Roller Screed.

The Roller Screed comes in two widths, 24" and 32" wide. The 24" wide holds 2,325 cubic inches of mortar, while the 32" wide holds 3,810 cubic inches of mortar. The deflector plate dispenses mortar up to 1" thick, extends past the hopper to reduce lap marks, and easily adjusts with wing nuts. Both sizes are made of heavy gauge steel that will tolerate flame burning to remove cured epoxy. The handle is aligned at 165 degrees for a convenient resting position and is shaped to permit the dumping of mortar directly from a wheelbarrow. The handle and wheels are pinned for easy removal to clean or transport, and a utility tray conveniently holds support tools.

Item Description Part #

24" Wide Roller Screed HT-WRS-24

32" Wide Roller Screed HT-WRS-32

Air Compressors

HoverTrowel has requisitioned Emglo to manufacture portable air compressors to our specifications and Ingersoll-Rand's motor requirements. These compressors are performance-rated and designed to provide years of efficient and reliable service. There are two models available and both can be configured with a three-phase 460-volt motor on special order.

The Emglo model G5A-38P is a 4-cylinder, single-stage unit mounted on a 30-gallon ASME code receiver. Powered by a 5 HP motor, this compressor delivers 18.3 CFM of air at 100 PSI. The unit is available with either a single-phase 230 volt motor or a three-phase 460 volt motor. Both single-phase and three-phase models include a motor starter and on/off switch as standard equipment. The 30-gallon portable design is well-balanced for ease of movement. A 3/8 NPT regulator and gauge assembly is mounted for easy connection to the air hose.

The Emglo model J5A-30P is the biggest electric-wheeled portable compressor available. This four-cylinder pump comes mounted on a 30-gallon ASME portable tank. Its 5 HP motor is able to deliver 19.8 CFM of air at 100 PSI. The unit is available with either a single-phase 230 volt motor or a three-phase 460 volt motor. Both single-phase and three-phase models include a motor starter and on/off switch as standard equipment. This heavy-duty 30-gallon portable unit has 10" diameter pneumatic tires for easy movement at the job site.

Air Filters

Air filters are extremely important in maintaining a good working pneumatic motor by removing condensed water and foreign particulates. The compressor-supplied air enters the filter and travels through 7 layers of filter material before exiting through the outlet port. Both have pressure gauges, relief valves set at 125 psig and output lines of 3/8" NPT (Fem.). These stand alone filters also act as a reducer for larger incoming air lines. The 2 line model weighs 24 lbs. while the 6 line model is 28 lbs.

Ingersoll-Rand Kits

• Lubricating Kit
• Gauge Kit
• Needle Care Kit